RATES VARY Call for quotes! (843) 267-3773

SLIDES AND BARRELS .
1. Fit slide to receiver 150.00
2. Fit oversized match barrel (Labor Only) 150.00
3. Throat barrel & Polish feed ramp on receiver 40.00
4. Lower ejection port 50.00
. .
RECEIVER OPTIONS .
1. Checker front strap 20 lines per inch 225.00
2. Stipple front strap 100.00
3. Checker mainspring housing 20 lines per inch 50.00
4. Stipple mainspring housing 25.00
(All receiver work will require refinishing at additional charge) .
. .
SIGHTS .
1. Bo-Mar BMCS sight with silver soldered front sight, CMP legal includes refinishing 175.00
2. Install fixed sight set with staked front sight (Labor Only) 40.00
3. Optics mounts POR
. .
TRIGGER WORK .
1. Trigger job 3 ½ pounds or greater (If required, parts are additional charge) 75.00
2. Trigger job of 3 ½ pounds of less (Requires quality parts, if needed, at additional charge) 100.00
3. Install and fit new trigger (Labor Only) 25.00
. .
SAFETIES
1. Install beavertail grip safety & refinish receiver in matte black oxide 100.00
2. Install extended single side thumb safety (Labor Only) 25.00
3. Install ambi thumb safety (Labor Only) 50.00
. .
OTHER ODDS AND ENDS .
1. Provide and fit extended ejector 50.00
2. Provide, fit and tune extractor 50.00
3. Refit and tune your extractor 35.00
. .
SMITH AND WESSON MODEL 41 .
1. Trigger job 65.00
2. Modify ejector/slide stop and refit bolt to slide 100.00
3. Fit barrel assembly to receiver 75.00
. .
SMITH & WESSON REVOLVERS .
1. Trigger job K or L frame 50.00
2. Trigger job N frame 60.00
3. Trigger job J frame 65.00
4. Re-time cylinder (hand included) 75.00
5. Remove End-Shake from cylinder 75.00
6. Remove End-Shake from yoke 40.00
. .
I am pleased to be using EGW components along with Caspian slides and receivers on all new pistols that I build. If you do not have a pistol on which to start your build, I can provide the above listed components to use as the base to start your new gun. The initial cost for these parts would be $735.00
CMP HARDBALL .45 .
On your government style .45 (subject to acceptance), I will fit the slide to the receiver and install a Bar-Sto national match barrel; lower the ejection port fit an extended ejector and tune the extractor for positive and consistent functioning; fit a new trigger and set the trigger pull to a legal 4 pounds; Bomar sights will provide the best possible sight picture; the front strap and mainspring housing will be stippled for a solid grip and the pistol will be finished in a matte black oxide. The price for this package is $1250.00 Deposit of $500.00 required to start work Price does not include shipping
. .
NRA WADCUTTER .45 .
On any government style automatic (subject to acceptance), I will fit the slide to the receiver (hand lapped); install a national match barrel; lower the ejection port, fit an extended ejector, and tune the extractor for total reliability; fit a new trigger, long or short (your choice) and set the trigger to a clean 3 1/2 pounds; stipple the front strap and mainspring housing for a good grip. Your choice of sights may be added to this package, price to be determined. The whole gun will be finished in a matte black oxide. The price for the above package is $1500.00 Deposit of $650.00 required to start work Price does not include shipping
. .
I am very pleased to offer a 10% discount on labor only to all active duty military and law enforcement personnel. .